Hydev

This is an old revision of the document!

---

# USense

## Overview

Well, this project is a little, quick, and fun one. Basically, the idea was to see what could be done with some RGB leds and capacitive touch inputs.

## Pictures

## PCB ### Version 1

### Version 2

## Firmware

### Test firmware

Since I don't have too much spare time, I only wrote a quick firmware to test the board and be able to give the v2 to a friend. - The RGB led pulses/fades from one color to another automatically - One capacitive input increases the fading speed - The other decreases the speed - The two combined change the color changing cycle

### Protocol

	Messages are 8 bytes long (since it is the limit for wMaxPacketSize for low-speed USB devices)
	
	[ Mode ] [ Val0 ] [ Val1 ] [ Val2 ] [ Val3 ] [ Val4 ] [ Val5 ] [ Val6 ]
	
	* PC > USense *********************************************************
	
	[ 0x01 ] Fade On
			[ 0xRR ] Maximum brightness Red
			[ 0xGG ] Maximum brightness Green
			[ 0xBB ] Maximum brightness Blue
	[ 0x02 ] Fade Off
	[ 0x03 ] Get Fade
	
	[ 0x04 ] Set Fade Steps
			[ 0xVV ] 0x00-020
	[ 0x05 ] Get Fade Steps
	
	[ 0x06 ] Set Fade Delay
	[ 0x07 ] Get Fade Delay
	
	[ 0x10 ] Set Fixed color 
			[ 0xRR ] [ OxGG ] [ 0xBB ]			
	[ 0x11 ] Get LEDs color
	[ 0x12 ] LEDs Off
	
	[ 0x20 ] Get Touch
	[ 0x21 ] Enable Touch INT
	[ 0x22 ] Disable Touch INT
	[ 0x23 ] Get Touch INT
	[ 0x24 ] Enable Touch ACT
	[ 0x25 ] Disable Touch ACT
	[ 0x26 ] Get Touch ACT
	
	[ 0x30 ] Get Fade Mode
	[ 0x31 ] Set Fade Mode
	
	[ 0x80 ] Reset
	
	* Usense > PC *********************************************************
	
	Usually, it's just an Ack so:
	[ 0xRR ] [ 0xAA ]
					[ 0xRR ] The request code (see PC > USense)
					[ 0xAA ] Ack (0x42) or NAck (0xFF) Value for the previous request
	
	For the "Get" requests, it's an Ack, then the value:
	[ 0xRR ] [ 0xAA ] [ 0xV1 ] [ 0xV2 ] ...
					[ 0xRR ] The request code (see PC > USense)
					[ 0xAA ] Ack (0x42) or NAck (0xFF) Value for the previous request
					[ 0xV1 ] ... The returned Value
	ex:
	Get LEDs color
	[ 0x11 ] [ 0x42 ] [ 0xRR ] [ 0xGG ] [ 0xBB ] [ 0xrr ] [ 0xgg ] [ 0xbb ]
			in capital letters: Value
			in small letters: maximum fvalue for fading stuff
	
	Get Touch
	[ 0x23 ] [ 0x42 ] [ 0xVV ] Returns Inputs mask
					[ 0xVV ] Touch inputs mask (0b1 means pressed, 0b0 means released)
	
	Special case: for the "INT" messages, the auto-ack is 0x24 instead of 0x42
	ex: Touch INT 
	[ 0x23 ] [ 0x24 ] [ 0xVV ] Touch INT message
					[ 0xVV ] See above